35 Search Results

Heat pipes are advanced passive thermal management devices that utilize phase change and capillary action to achieve efficient heat transfer. However, due to the complexity of the phenomena coupled in heat pipes, including capillary, phase change, turbulence, and compressibility effects, there are high uncertainties in the predictability of their operational regimes and performance. This PIRT exercise, conducted as a collaborative effort involving the Department of Energy (DOE) Microreactor Program (MRP), the Nuclear Regulatory Commission (NRC), and university partners systematically identifies, reviews, and prioritizes critical phenomena affecting the operation of heat pipes based on their importance and knowledge levels. Additional analysesmore » and discussion are provided for phenomena with high importance and low knowledge, such as wick de-wetting, critical heat flux, contact angles, and pressure dynamics. The discussions included the recognizing challenges and proposing future research directions for both modeling and simulation and experimental efforts. Additionally, the report addresses phenomena with medium importance and low knowledge that could impact heat pipe operation during non-normal or transient operation, including frozen startup, laminar to turbulent transition, geyser boiling, wick priming, underfilling conditions, surface roughness of the wick, NCGs trapped in the wick, and the timescales of startup and shutdown. In conclusion, this comprehensive evaluation serves as a valuable resource for guiding future research and development efforts, supporting the successful integration of heat pipes into critical applications such as nuclear reactors, and contributing to the advancement of heat pipe technologies in safety-critical industries.« less

Here, in this study, we combined experimental and theoretical methods to investigate the structural sensitivity of metal catalysts in the ethylene hydroformylation reaction. Among Rh, Pt, Ir, Ni, Au, Ag, Pd, and Cu catalysts studied using experimental and theoretical methods, Rh showed the highest selectivity toward the C-C coupling product from CO and C₂H₅ (i.e., C₂H₅CHO). The results from DFT and microkinetic simulations revealed that the activation energy barrier for C-C coupling is lowest on the Rh nanocluster, which explains the experimentally observed highest C₂H₅CHO selectivity on the Rh catalyst. Furthermore, DFT results demonstrated that the sites located on themore » flat surfaces of nanoparticles primarily promote the hydrogenation reaction, leading to the formation of undesired C₂H₆. In contrast, undercoordinated edge and corner sites of the nanocluster promote the C-C coupling reaction. Thus, our results illustrate that the selectivity toward C₃ oxygenates in ethylene hydroformylation reaction can be steered by tuning the size of Rh nanoparticles (the best-performing catalyst) to optimize the active (edge and corner) sites that preferentially promote the C-C coupling reaction.« less

Rare earth element exploration requires a quantitative understanding of factors governing their mobilization and economic concentration. However, the behavior of rare earth elements in carbonate- bearing hydrothermal fluids associated with carbonatite-hosted deposits is poorly understood, and conflicting mechanisms of rare earth transport by anionic ligands and alkali behavior have been described. Here, we report quantitative data to characterize the role of carbonate-bearing solutions in the hydrothermal mobilization of neodymium. Solubility studies of neodymium phosphate were performed at temperatures ranging from 100 to 600 °C in carbonate-bearing solutions. The thermodynamic data determined for the predominant complex were used to model themore » separation of neodymium from thorium in a simple flow-through system based on fluid and mineral compositions characteristic of carbonatite deposits. Our data suggest that neodymium transport is controlled by the stability of the carbonate species NdCO₃OH^o , and at temperatures of 500–600 °C, the concentrations of neodymium in solutions can reach ~1000 ppm.« less

Abstract We have demonstrated for the first time that turbulent plasma density fluctuations in the edge of the DIII-D tokamak are responsible for substantial broadening of an injected microwave beam by successful quantitative comparison between experimental observations and first principles 2D full-wave simulations. The broadening of the beam has important implications for control of tokamak discharges through localized electron cyclotron deposition needed for eliminating magnetohydrodynamic instabilities. This new predictive capability is mandatory to design & operate present & future tokamaks in such a way that microwave heating schemes achieve their intended objectives.

Heat pipe microreactors are reactor designs that primarily use liquid-metal heat pipes to cool the core. The main interest in heat pipes is the fact that they can remove heat passively. This, along with the use of liquid metal, allows the reactor to operate at higher temperatures. Although the use of heat pipes in nuclear reactors is new, liquid-metal heat pipe technology is mature. Nevertheless, experimental data on heat pipes are scarce, and very little is known about their behavior during abnormal operations and close to their thermal limits. Therefore, new experiments and accurate heat pipe simulations are needed tomore » develop reliable closure models. This work describes a joint experimental and numerical investigation into heat pipes that attempts an initial closure of this gap. Further, the numerical and experimental efforts are currently proceeding in parallel, aimed at different aspects of heat pipes. The numerical part is focused on gaps in local closures, and the experiments capture the overall heat pipe behavior.« less

We present the analysis of two-particle angular correlations using coordinate systems defined with the conventional beam axis and the event thrust axis. We propose the latter as a good representation for the correlation structure interpretation in the e⁺e^- collision system. The e⁺e^- collisions to hadronic final states at center-of-mass energies of $$\sqrt{s}$$ = 10.52 GeV and 10.58 GeV are recorded by the Belle detector at KEKB. In this paper, results on the first dataset are supplementary to the previous Belle publication [1]. At the same time, the latter is the first two-particle correlation measurement at collision energy on the Υ(4S)more » resonance and is sensitive to its decay products. Measurements are reported as a function of the charged-particle multiplicity. Finally, a qualitative understanding of the correlation structure is discussed using a combination of Monte Carlo simulations and experimental data.« less

The National Criticality Experiments Research Center (NCERC) located at the Nevada National Security Site (NNSS) in the Device Assembly Facility (DAF) and operated by Los Alamos National Laboratory (LANL) is the only general purpose critical experiments facility in the United States. Experiments from subcritical to critical and above prompt critical are carried out at NCERC on a regular basis. In recent years, NCERC has become more involved in experiments related to nuclear energy, including the Kilopower/KRUSTY demonstration and the recent Hypatia experiment. Multiple nuclear energy related projects are currently ongoing at NCERC. This paper discusses NCERC’s role in advanced reactormore » design and how that role may change in the future.« less

Subduction megathrusts exhibit a spectrum of slip modes, including catastrophic earthquakes. Although the mechanical and frictional properties of materials sampled from subduction zones have been studied extensively, few datasets have been collected for compositions and at pressure and temperature conditions representative of those in situ. The Nankai subduction zone in southwest Japan is a well-studied margin, and abundant data provide an opportunity to advance our understanding of fault and earthquake physics. Here, we use samples exhumed in the Shimanto and Sanbagawa Belts on Shikoku Island of southwest Japan that represent analogs for materials along the present-day megathrust at depths ofmore » ~5–>25 km, and we shear these at their peak in situ pressure-temperature (P-T) conditions. Effective normal stresses range from 28 to 192 MPa, and temperatures from 105°C to 470°C. We used pore fluid pressures of 45–240 MPa, corresponding to fluid overpressure ratios λ of 0.65 and 0.90. Slip velocities of 0.1–100 μm/s were used, in order to focus on the nucleation of instability and earthquakes. We found predominantly velocity-strengthening (inherently stable) behavior under all conditions for λ = 0.65. For λ = 0.90, velocity-weakening behavior was observed at 350°C, with velocity-strengthening behavior at lower and higher temperatures. The rate/state frictional stability parameter (a-b) increases with slip velocity at temperatures up to ~200°C and remains constant or decreases with slip velocity at higher temperatures. Altogether, our results demonstrate the potentially important roles of both temperature and slip velocity in controlling the distribution of stress and frictional rheology along subduction thrusts.« less

We present a search for the charged lepton-flavor-violating decays Υ(1S) → ℓ^±ℓ'^∓ and radiative charged lepton-flavour-violating decays Υ(1S) → γ^ℓ±ℓ'∓ [ℓ,ℓ' = e, μ, τ] using the 158 million Υ(2S) sample collected by the Belle detector at the KEKB collider. This search uses Υ(1S) mesons produced in Υ(2S) → π⁺π^– Υ(1S) transitions. We do not find any significant signal, so we provide upper limits on the branching fractions at the 90% confidence level.

Epoxy underfills can be implemented in electronic packaging to enhance solder joint reliability of surface mounted components. However, it is important for an engineer to have a failure criterion that can be used for failure predictions and redesign of electronic assemblies. For this study, data from epoxy bond failure in mock electronic part assemblies were correlated to finite element analyses to predict adhesive failure initiation. Experiments were performed to determine failure loads for various loading locations and nonlinear viscoelastic analyses were performed for the same loading locations to determine a maximum principal strain failure parameter. Predictions showed that a maximummore » principal strain failure parameter defined from one test could be used as an indicator of adhesive failure of an epoxy bond undergoing other modes of loading. Failure initiation predictions matched experimental data using a maximum principal strain failure parameter for an epoxy bond undergoing mixed modes of loading for both unfilled and alumina oxide filled 828DEA epoxy. Such experimental setup is deemed appropriate for future epoxy testing.« less